
Protect pitted, porous stone around the pool
Travertine Sealing in Oldsmar, FL
Pitted travertine by an Oldsmar pool can be protected, so call (656) 254-5347 for a free estimate.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Can I get travertine sealing in Oldsmar, and how soon?
A local contractor who covers Oldsmar will answer your travertine sealing request within 1 business day, and usually well before that. The estimate costs nothing, and a no is a fine answer. To start, call (656) 254-5347.
Travertine is a pitted, porous natural stone, so it soaks up pool splash, sprinkler water and spilled drinks faster than a dense paver does. A sealer slows that down, which means a spill sits on the surface long enough to be cleaned off. Name the stone areas, such as the lanai, the pool apron or the front steps, when you send the short estimate form.
Tell the contractor if some of your hardscape is concrete paver and some is stone, because the two take different care. The contractor can then price each area on its own.

Why does travertine soak up water so fast?
Travertine forms from fresh water limestone, and Wikipedia says fresh deposits can be about 10 to 70 percent open space. Those tiny voids pull in water and anything dissolved in it. On an Oldsmar pool deck that means chlorine splash, suntan lotion and sprinkler water all find a way in. To have your stone checked, call (656) 254-5347.
One Tampa Bay company puts the result in plain terms: unsealed stone pavers absorb moisture, lose joint sand, fade and grow dark algae. Pinellas County adds to that, with summer highs in the low 90s and an almost daily chance of afternoon thundershowers. A damp surface that stays damp is where the dark patches begin. To plan a fix, send the short estimate form.
Color matters here too. Pure travertine is white, and Wikipedia says impurities turn it brown, yellow, grey or coral red. Stone that has been rained on and shaded for years often looks flat next to a freshly cleaned sample. Bring a photo of the oldest and newest spots when you call (656) 254-5347.
How is sealing travertine different from sealing concrete pavers?
The steps look alike, but the stone behaves differently. Unilock says concrete, brick and natural stone absorb at different rates, and a sealer made for concrete pavers may not be ideal for every stone. That is why the product choice is a real question for travertine, and why you should ask what the label says about stone. To raise it with a contractor, send the short estimate form.
Absorbency
Open pores drink sealer unevenly. A contractor tests a small area first, which is also Unilock's advice for avoiding a whitish film.
Pits and voids
Holes in the face of the stone collect dirt and water. They are cleaned out before sealing so the coat does not lock grime in.
Joints
Stone joints can lose sand just like paver joints. Fresh sand goes in before sealer, so the pieces stay put.
Finish
Gloss, satin and matte all change how the stone looks and feels underfoot. A sample patch settles the question before the whole deck is done.
Where near Oldsmar can a contractor seal travertine?
A local contractor serves Oldsmar and the communities around it. Each town below has its own page with local notes on paver work, and the same contractor reach applies to stone. Not sure your street is covered? Call (656) 254-5347.
Can the wrong cleaner damage travertine?
Yes, and it happens more often than owners expect. Travertine is calcium carbonate, and Wikipedia notes that calcium carbonate reacts with acids and that acid rain wears limestone buildings. Unilock adds that acid-based efflorescence removers can slightly change the color of paving. A strong product on the wrong stone can leave a dull spot that sealer will not hide. To ask about safe options, call (656) 254-5347.
Tools matter as well. Unilock warns that a wire brush leaves metal particles that rust, and that the wrong pressure or nozzle can erode paving and blow out joint sand. One Tampa Bay company says light consumer washers can strip sand and etch stone. This page is not a cleaning guide, and the safe move is to let the contractor choose the method and test it on a hidden spot. Ask how they will test when you send the short estimate form.

Does a travertine pool deck need a non-slip finish?
Ask for one, because a stone deck is walked on wet and barefoot. Unilock says high gloss finishes can be slippery when wet and that a matte sealer keeps more traction. Pool decks also take splash and sunscreen, which Unilock lists among the reasons to seal. A satin or matte product protects the stone without turning the deck into a slide. To talk about traction, call (656) 254-5347.
Before the finish goes on, the contractor can try it on a small patch so you see the sheen in your own light. Screened lanais and open decks look different at noon and at dusk. Wait for the patch to dry, then decide when you send the short estimate form.
What if my travertine is at a condo or townhome community?
Many Oldsmar homes share walls and common areas. In ZIP code 34677, Census estimates count 10,218 housing units, with 6,909 single-family homes and 2,821 multi-family units, about 28 percent of the total. If your building has an association, ask the board whether a sealer or a change in sheen needs approval before work starts. To plan around a community calendar, send the short estimate form.
About 80.5 percent of occupied homes in that ZIP are owner occupied, so most stone around here belongs to the household that walks on it. That makes the choice yours in a single-family yard and a shared choice in a managed community. Say which kind of home you have when you call (656) 254-5347.
Will sealing fix standing water on my travertine?
No. Unilock says sealing is not a cure for drainage or a weak base. Oldsmar sits at the northern tip of Tampa Bay at about 13 feet above sea level, and the town rests on a plateau that never rises over 20 feet. Water drains slowly on flat ground, and UF/IFAS says builders often bring in fill to raise a lot. If a corner of your stone stays wet after rain, mention it when you send the short estimate form.
What does travertine sealing cost in Oldsmar?
No company page read for this guide publishes a travertine price, so this section builds one from the published pieces that do exist. One Tampa Bay company lists $1.50 to $2.50 per square foot for Oldsmar to wash, re-sand and seal pavers, and a flat $199 to wash a two car paver driveway. Travertine is not on either list, which is why the table below is labeled a range for pavers. To get a real number, call (656) 254-5347.
Three things move a stone quote: how pitted the surface is, how much old sealer or staining sits on it, and whether the joints need fresh sand. Steps and curved edges also add time. The same company says stain removal and stripping old sealer are set on a walk-through and not priced online. Send photos of the worst areas when you send the short estimate form.
| Stone area | Typical example | Wash, re-sand and seal (range for pavers) |
|---|---|---|
| 200 sq ft | Entry landing or lanai corner | $300 to $500 |
| 500 sq ft | Pool deck apron and steps | $750 to $1,250 |
| 800 sq ft | Whole screened pool deck | $1,200 to $2,000 |
| 1,200 sq ft | Pool deck plus covered patio | $1,800 to $3,000 |
No company page read for this guide publishes a travertine rate. One Tampa Bay company lists travertine sealing as a service but gives no price, so this table uses the $1.50 to $2.50 per square foot it publishes for Oldsmar pavers, which covers rotary washing, re-sanding and two coats of acrylic sealer. Natural stone can be priced differently once a contractor sees the pits and joints, so treat the figures as a starting point.
How often does travertine need another coat?
Plan on the same three to five years that Unilock and Belgard give for pavers, and check sooner on busy or sunny areas. A simple test is to flick water on the stone: if it beads, the coat is working, and if it darkens and sinks in, it is thin. Summer in Pinellas County brings nearly two thirds of the year's rain between June and September, so the wet season shows weak spots fast. To book a check, call (656) 254-5347.
Belgard also says sealer should go on no more than once in three years, with at most two applications, because too many coats leave a film that can discolor. A contractor who offers a fresh coat every year is working against that guidance. Ask for the reason behind any schedule when you send the short estimate form.
What does sealed stone look like near an Oldsmar pool?








How does the travertine sealing process work?
The process has five steps, and the order protects the stone. Skipping the test patch or the dry time is where most stone jobs go wrong. To get on a schedule, call (656) 254-5347.
1. Look and test
The contractor studies the stone, checks for old sealer, stains and loose pieces, and tries the product on a hidden corner.
2. Gentle wash
A low pressure wash lifts dirt and algae. Spray stays at or under the 30 degree angle Unilock suggests, so sand is not blown out.
3. Dry and refill
Western Interlock says hidden moisture stops sealer from bonding, so the stone dries fully and joints are topped up with sand.
4. Seal in the cool hours
Western Interlock says sealer can fail above 90 degrees on the surface, and stone in full sun runs hot. Early starts and shaded hours help.
5. Cure and walk through
The contractor gives the wait times, keeps sprinklers off the deck and shows you the result.
What do Oldsmar homeowners ask about travertine sealing?
How often should I seal pavers in Florida?
Many owners reapply every three to five years, according to Unilock, and busy areas can need a recoat sooner. Belgard gives the same three to five years. Travertine has no separate number in those guides, so a contractor judges it by how fast water stops beading.
How much does it cost to seal travertine pavers?
No company page read for this guide lists a travertine price. The Oldsmar rate one Tampa Bay company publishes for pavers is $1.50 to $2.50 per square foot, and stone is quoted after the contractor sees the surface. For a figure on yours, send the short estimate form.
Which sealer works best for pavers in Florida?
Unilock says coastal and sunny parts of Florida gain from a sealer with strong resistance to UV light and salt, and that a sealer made for concrete may not suit every natural stone. Ask the contractor why the chosen product fits travertine in particular.
Does travertine need sealing around a pool?
Unilock says pool decks collect splash and sunscreen, which sealers help resist. Travertine is porous, with fresh deposits ranging from about 10 to 70 percent open space, so unsealed stone takes in whatever lands on it.
Will sealed travertine turn slippery?
A high gloss coat can, and Unilock warns about it when the surface is wet. A matte or low sheen product keeps more grip, so say the stone is by a pool when you ask for a quote.
Can an acid cleaner harm travertine?
Travertine is calcium carbonate, and Wikipedia notes that calcium carbonate reacts with acids. Unilock says acid-based removers can shift the color of paving. A contractor tests a small hidden spot before using anything strong.
What are the holes in my travertine, and should they be filled?
Pitting is part of how the stone forms, and Wikipedia notes the surface often shows holes and troughs. Whether to fill them is a question for the stone and the look you want. Ask about it when you send the short estimate form.
Is a pressure washer safe on travertine?
Not at high settings. One Tampa Bay company says light consumer washers can strip sand and etch stone, and Unilock says wrong pressure or nozzle settings can erode paving and blow out joint sand. Spray at or under 30 degrees is the angle Unilock suggests.
Does sealing stop travertine from fading in Oldsmar sun?
It slows it. Unilock says sealers with UV resistance help in sunny parts of Florida, and one Tampa Bay company says unsealed stone pavers fade. Shade, sprinklers and daily wear all change how long the color holds.
How long before I can use a sealed pool deck?
One Tampa Bay company lists about 24 hours before foot traffic and 48 before vehicles for pavers, and Unilock wants two dry days for the sealer to cure. Plan the pool schedule around that.
Ready to protect your stone? Ask for a travertine estimate
Phone in or fill out the short form. Someone local gets back to you inside 1 business day, often far sooner, and the estimate costs nothing.
Free, no obligation
