Click To Call(656) 254-5347Click To Get A Free Estimate
Red and tan brick paver walkway leading to a front entry with a freshly sealed sheen

Brick paver color that stays rich and even

Brick Paver Sealing in Oldsmar, FL

Call (656) 254-5347 to ask for a free brick paver sealing estimate in Oldsmar, FL.

  • Brings out deeper paver color
  • Fresh joint sand helps lock pavers in place
  • Gives weeds less room to grow
  • Makes the surface easier to keep clean
  • Free estimate, no obligation

Request a Free Estimate

Free, no obligation.

Step 1 of 2

Where are your pavers?

Please choose one.

Free EstimateNo obligation
Fast ReplyWithin 1 business day, usually much sooner
Typical Local Price$1.50 to $2.50 a sq ft to clean, sand and seal
Call Now(656) 254-5347

Who seals brick pavers in Oldsmar, and how quickly do they reply?

A local contractor takes on brick paver sealing in Oldsmar, and you will get a reply within 1 business day, often much sooner. The estimate is free, with no pressure to hire. To talk it over by phone, call (656) 254-5347.

Brick pavers fade, collect green film in the shade and lose joint sand like any other paver, but brick soaks up water and stains faster than concrete. A clean, sealed brick surface keeps its warm color, sheds splashes and washes up more easily. Mention whether the brick is old or new when you send the short estimate form.

Call (656) 254-5347

Is my brick clay or concrete, and does that change the sealer?

It can, which is why the first visit identifies the material. Clay brick and concrete pavers shaped like brick take different products. Unilock says brick pavers are more absorbent than concrete and usually need a matte or low gloss sealer. Rochester Cement Products says penetrating sealers leave little to no gloss, while topical sealers form a film on top. To have a contractor check yours, call (656) 254-5347.

Color is the other piece. The same company says solvent-based sealers may give richer color and water-based ones a more natural finish. Lurvey's adds that the change in color varies by material, so test first. Ask to see a corner done before the full job, and send the short estimate form.

Brick paver entry walk with a gloved hand brushing joint sand beside a flower bed

Natural or wet look: which finish suits brick pavers?

A natural finish keeps the brick looking like brick. A wet look deepens the red and brown tones and adds shine. One Tampa Bay brick paver company offers both, and a penetrating sealer is the usual route to the natural look. Gloss has a price, since Unilock warns it is slippery when wet. To choose for an entry or a walk, call (656) 254-5347.

Rochester Cement Products says topical sealers can yellow, wear unevenly or trap moisture as they age, and that high gloss needs more frequent upkeep. That matters on brick in shaded beds where moisture hangs around. Find out which kind is planned, and why, when you send the short estimate form.

Pricing

What does brick paver sealing cost in Oldsmar?

One Tampa Bay company publishes $1.50 to $2.50 per square foot for Oldsmar to wash, re-sand and seal, and no source lists a rate for brick on its own. The table uses that range with brick-size examples. Brick often soaks up more sealer per square foot, which can nudge material cost upward. For a price on your brick, send the short estimate form.

Repairs change the number. Efflorescence treatment, stripping an old coat and relaying settled brick are usually extra. A wash alone is much cheaper, and the cleaning guide lays out that price. To ask for both numbers side by side, call (656) 254-5347.

Brick areaExampleWash, sand and seal
150 sq ftFront walk and entry$225 to $375
350 sq ftBrick patio or courtyard$525 to $875
600 sq ftBrick driveway$900 to $1,500
900 sq ftDriveway, walk and entry together$1,350 to $2,250

Math uses the $1.50 to $2.50 per square foot one Tampa Bay paver company publishes for Oldsmar. No source lists a brick-only rate, so the table is built from that published range. Sizes are examples.

Get a Free Estimate

How it works

How does the brick sealing process work in Oldsmar?

The brick sealing process runs in five steps. The first two decide the product, and the last three apply it. To book a look at your brick, call (656) 254-5347.

1. Identify the material

The contractor confirms whether the surface is clay brick, concrete made to look like brick or a mix, because the sealer choice depends on it. A past coat is looked for as well.

2. Test for an old sealer

A small wet spot shows whether water beads or soaks in. Lurvey's says never to put a new sealer over an incompatible coating, so a mystery coat is tested first.

3. Clean and dry the brick

Dirt, algae and white haze come off with a gentle wash, and acid cleaners are chosen only when the brick allows them. The surface then dries fully before anything is applied.

4. Fix the joints

Worn joints get fresh sand, polymeric where the layout calls for it. Joints are the weak point in brick fields because rain and weeds work at them first.

5. Apply the chosen finish

A penetrating sealer for a natural look, or a film-forming one for a richer or wet look, goes on thin and even. A test corner is done first, as Unilock suggests.

What happens if an old sealer is already on my brick?

The old coat decides the plan. Lurvey's says never to place a new sealer over an incompatible coating and that neither solvent nor water-based sealers are automatically right. Unilock lists an earlier incompatible product as one cause of a whitish film. A water bead test and a small test patch show what is down. To ask for one, call (656) 254-5347.

If the old coat is failing, it is stripped before the new one goes on. Belgard says no more than two applications and no more than one every three years, because extra layers can discolor. A contractor who will not say what is already on your brick is a reason to ask again when you send the short estimate form.

How do I get rid of white haze before sealing brick?

White haze is usually efflorescence, which Lurvey's describes as a white or gray haze made when moisture carries soluble salts to the surface and evaporates. It is usually not structural. Unilock says it fades in two to three months and sometimes up to a year, and Belgard says to wait at least 30 days after installation to seal. To ask whether yours is salt or sealer, call (656) 254-5347.

Acid cleaners remove it from compatible surfaces, but they can shift color, so they are tested first. Sealing over haze locks it in. If your brick is new, tell the contractor the install date when you send the short estimate form.

Homeowners and a contractor reviewing a brick paver sample board beside an Oldsmar front walk

Do older brick walkways and courtyards in Oldsmar need special care?

Often, because Oldsmar has been building since Ransom E. Olds bought land here in 1916. Wikipedia says the Bank Building from 1918 sits downtown in the Mediterranean Revival style, faced in white Italian glazed brick, which shows how long masonry has mattered locally. Older brick runs have settled joints, past patches and mystery coats. To have yours looked over, call (656) 254-5347.

Many Oldsmar homes have brick entries and courtyards that are now decades old. Describe the age of your brick when you send the short estimate form.

How does Oldsmar's humid air affect brick pavers?

Humidity keeps brick damp, and damp brick grows algae. One Tampa Bay company notes that Oldsmar's humidity keeps unsealed stone damp and encourages mold. Pinellas County sits on a peninsula, and Wikipedia says that adds large amounts of humidity, with nearly two thirds of the year's rain from June through September. To plan around the wet season, call (656) 254-5347.

Shade makes it worse. A brick walk under an oak or along a north wall may need a wash each spring, which is Belgard's suggestion, even if the sealer is newer than that. Ask about the schedule when you send the short estimate form.

What should I ask before hiring a brick paver sealing contractor in Oldsmar?

Ask what the brick is made of, what is on it now and what product is planned. A contractor who can answer all three has looked at your surface. Unilock says to test a small corner first, and Lurvey's says the color change varies by material, so a test corner also shows how deep the color goes. To set up a test corner, call (656) 254-5347.

Then ask for the price in writing with square feet, the coverage rate and the number of coats. Belgard caps sealer at two applications and no more than one every three years, so a plan for three coats is a reason to ask why. To get a written plan, send the short estimate form.

Does the flat, bay-side ground in Oldsmar matter for brick?

A little. Wikipedia says Oldsmar sits on a plateau that never rises above 20 feet and has about 10 miles of waterfront on Old Tampa Bay. Flat ground means water lingers after storms, and Unilock says sealing cannot cure poor drainage. Brick that stays wet grows green film and shows efflorescence sooner. To point out your wet spot, call (656) 254-5347.

Unilock also says coastal, sunny parts of Florida benefit from a sealer with UV and salt resistance. A product made for that exposure is a fair question for a brick entry that faces open sun. Ask what the product label says about it when you send the short estimate form.

Is brick paver sealing in Oldsmar worth it for an older home?

Often it is, when the brick is sound and the color has faded. Oldsmar homes come in every age, and ZIP code 34677 lists 10,218 housing units, 6,909 of them single-family. Sealing is optional, as Rochester Cement Products says, so the question is whether you want deeper color and easier cleanup. To weigh it for your Oldsmar entry, call (656) 254-5347.

If the brick is sound but dirty, a wash and fresh joint sand may be all an Oldsmar home needs. Sealing can follow once the surface is fully dry. Ask for both options priced when you send the short estimate form.

Can Oldsmar brick be sealed after a wash only?

Yes, after the brick is clean and dry. Lurvey's says to clean and fully dry the surface before sealing, and Unilock says shaded pavers can take about 24 hours to dry. A wash on Monday and sealer on Tuesday is a common plan for Oldsmar brick. To ask about the order, call (656) 254-5347.

Who decides when Oldsmar brick is dry enough?

The contractor does, and you can ask how it is checked. Unilock suggests warm, sunny conditions and 50 to 90 degrees Fahrenheit. A contractor who waits for a dry morning is protecting the coat on your Oldsmar brick. To ask about the dry test, send the short estimate form.

Photos

What do sealed brick pavers look like in Oldsmar?

Freshly sealed paver driveway at an Oldsmar entry
Sealed paver pool deck at an Oldsmar entry
Sealed paver patio behind the home at an Oldsmar entry
Sealed paver walkway to a front door at an Oldsmar entry
Close view of freshly sealed pavers at an Oldsmar entry
Paver area with one cleaned half beside a dirty half at an Oldsmar entry
Contractor cleaning pavers at an Oldsmar entry
Contractor sealing or sanding pavers at an Oldsmar entry

Which towns near Oldsmar get brick paver sealing?

A local contractor serves Oldsmar and the towns around it. Each place below has a page with its own notes. To ask about a street not listed, call (656) 254-5347.

Questions

Frequently Asked Questions

What is the average cost to seal pavers in Florida?

For brick pavers, Tampa Bay pricing starts from $1.50 to $2.50 per square foot, the range one company publishes for Oldsmar to wash, re-sand and seal. A 400 square foot brick walk and entry comes to about $600 to $1,000. To price your brick, send the short estimate form.

Is there a downside to sealing pavers?

There are three. The coat wears and has to be redone, a topical film can yellow or trap moisture as it ages, and the wrong product over an old one can cloud. Rochester Cement Products and Unilock both say as much. A test corner and a product match reduce the risk.

How much does it cost to seal outdoor pavers?

The same published range applies to brick, $1.50 to $2.50 per square foot in Oldsmar, with repairs and stripping extra. Brick soaks up more sealer than concrete, so the gallon count matters. Ask for the coverage rate from the product label in writing.

How often should I seal pavers in Florida?

Two paver makers, Unilock and Belgard, both give three to five years. Rochester Cement Products says some penetrating sealers last significantly longer than topical ones, while high gloss finishes need more frequent upkeep. Ask which kind is meant for your brick.

Do brick pavers in Oldsmar need sealing at all?

Not always. Rochester Cement Products says not every paver needs sealing, and some concrete pavers carry a factory coat. Sealing is worth it for color, stain resistance and easier cleaning, and brick near a grill or a garage sees more grease.

Should brick pavers get a wet look or a natural finish?

Both exist. One Tampa Bay brick paver company offers wet look or natural finish. Unilock says brick is more absorbent than concrete and usually calls for a matte or low gloss sealer, which keeps the natural look and a safer surface when wet.

Why is there white haze on my brick pavers?

Most likely efflorescence, calcium salts that rise with moisture and dry at the surface. Lurvey's says it is usually not structural but spoils the look, and that acid cleaners must be chosen with the material in mind. Sealing waits until the haze is gone and the brick is dry.

Let the brick keep its color.

Call, or use the short estimate form. A local contractor answers inside 1 business day, and often within hours.

Call (656) 254-5347

Free, no obligation